How To Build A Pc how to build a computer

Jimmy/ May 20, 2022/ how to build a computer

Take a look at your case and figure out where the PSU is supposed to go and how it can be oriented. Ideally, you want to orient the PSU so that its fan faces outside the case . If your case has a vent on the bottom, you can mount the PSU upside down, so long as the bottom vent will receive decent airflow when the PC is finished. When it’s fully seated, it will stand off the motherboard about a 35-degree angle. Push the SSD down and replace the tiny screw to lock it in place. Take the motherboard out of its antistatic packaging and put it on your work surface.

  • Install the power supply.Next we will be inserting the power supply.
  • RAM is the easiest hardware to install when you’re building a PC.
  • Align the notches on the module with the ridge in the slot then firmly press the module in until it clicks.
  • An indicator on CPU and motherboard will show you the correct orientation.

It links various components of a computer as well as handle communication and transmission between these components. When you start to understand how PC building work, there must be bunches of questions. You are not alone, we’ve listed some commonly asked questions and organized into several categories. Check the maximum amount of USB ports on the motherboard before purchasing a PC case.

Streamer Ultra Pro Streaming Pc

And I could list it all as I’m about to take my a+ cert, but that would be a ton. Focus on the front panel header connections which will be separate very small wires, with labels on each for switches and LEDs. Pass them through a case cutout to the front of the build . Place each RAM stick in a slot and push down evenly on both sides until the clips engage.

All of this can be done before windows or anything is installed. Congratulations, if you’ve made it this far you should have a fully assembled computer! After a final check to ensure there are no loose screws floating around in your case, and that all cables are clear of any moving parts, it’s time to power on your new computer. Finally, plug a 4 pin molex power connector into your hard drive. Hard Drive – The hard drive is the “long-term memory” of the computer.

Successfully building a computer is largely contingent on defining your computer goals and budget, buying the right parts, and putting everything together in the correct order. WikiHow marks an article as reader-approved once it receives enough positive feedback. This article received 23 testimonials and 80% of readers who voted found it helpful, earning it our reader-approved status.

He has over two years of experience writing and editing technology-related articles. Be sure to buy a power supply with the specific needs for your system and from a reputable company, as cheaper ones can be faulty and completely damage your system. Don’t touch the resistors and the pins on the CPU or the socket. Most of the time, a CPU comes with a heatsink, but if it is Intel and has a K on it (ex. Core i7 6700k, Core i5 6600k), you will most likely need to buy a separate fan.

Hyper Liquid Infinity X129 Ddr5 Gaming Pc

It will be labelled, and the pin outs will be different to the USB 2.0 headers. Install your USB 3.0 cables (denoted with a blue-colored end) into any available slots on the board, making sure to lineup the pins with the holes in the USB 3.0 cables. For the next step, you should slide the securing bracket back into its original position so it locks in place underneath the screw, and secure the retention arm back down. During this process the protective plastic cover should pop off, so don’t freak out if it comes flying at you. Be sure to stow the cover away in a safe place as it’ll protect the motherboard’s sensitive pins if you decide to remove the processor from the motherboard.

Plug the 4pin PWM fan connector on the end of the wire coming from your CPU fan into the CPU_FAN header on your motherboard at this stage. Lift the CPU retention bracket lever to reveal the socket and its pins. These are incredibly delicate and easy to bend , so be very careful when working around the socket. If you aren’t gaming or editing video, you’ll want to make sure your CPU supports integrated graphics.

Only necessary for gaming and editing PCs—regular PCs should be fine with a stock cooler.

Step 2: Mount Motherboard

These things go directly into your motherboard and is not designed to be placed in any drive bays. Refer to your motherboard manual to see where the CPU fan slot is located. If it doesn’t align properly, then pick it up and make sure it’s placed properly and that none of the pins are damaged. During the next 3 steps, we will be outfitting the motherboard prior to installing it. If you’re using an old case, then you might need to push the case firmly against the inside wall of the case before you lock it in place with the four screws. Or put another way, don’t be afraid to search for more info while building your PC if you are uncomfortable.

Share this Post